How to Remove Kitchen Faucet Handle

How to Remove Kitchen Faucet Handle?

The kitchen sink is one of the busiest places in our homes. With regular use, it can become clogged with food particles and other contaminates – and even parts of the faucet may become worn out or stuck.

If your dishwashing adventures have taken a toll on your kitchen tap handle, don’t despair!

Removing the handle from a standard kitchen faucet is actually easy with just some basic tools and patience.

In this post, we will walk through how to properly remove your faucet handle in just 5 simple steps. So if you’re ready to get started updating or replacing that old kitchen staple, keep reading!

How Do You Remove a Screwless Faucet Handle?

Removing a screwless faucet handle is not as difficult as it may seem. First, you need to locate the set screws located under the handle or at its base. These screws must be loosened in order to allow the handle to come off.

If there are no visible set screws, use a flathead screwdriver and pry off the decorative cap covering them.

Once these have been removed, use your fingers or an Allen wrench (hex key) to hold onto one of the exposed screws while you turn the other with a Phillips-head screwdriver (cross tip).

This will loosen both set screws and allow you to pull out the faucet’s inner assembly from within the sink top.

Finally, grab the handle from its base and give it a gentle twist to the left or right.

This will cause the handle to come loose from the inner assembly and you can then easily remove it from its mount. Once finished, your screwless faucet handle should be removed without much difficulty.

If you have any remaining problems, consult your local hardware store for further assistance. They can also provide specific instructions on how to properly install new faucet handles if needed.

How Do You Remove a Faucet Tap Handle?

Removing a faucet tap handle is a relatively straightforward process, with the main difficulty being access to the nuts and washers underneath.

In general, you will need an adjustable wrench or pliers to loosen the nuts and unscrew them from the spout.

Before attempting to remove your faucet tap handle, make sure that you have turned off the water supply valve beneath the sink. This can help prevent any unwanted messes while doing this job.

To begin removing a faucet tap handle:

1. Look under the sink for access points where you can see all of the parts connected to your faucet including valves, nuts and washers.

2. Place an adjustable wrench over each of the nuts and turn them counter clockwise until they are loose.

3. Pull the handle away from the faucet body and set aside.

4. Unscrew all of the parts connected to your tap, including washers and other small components.

5. Clean up any remaining debris or dirt that you may find where your tap used to be situated.

6. When finished, simply reassemble in reverse order as above to replace the faucet tap handle!

If you encounter any difficulty along the way, do not hesitate to seek professional help for a more secure solution that is tailored to your particular situation.

Read: Can’t get kitchen faucet handle off

Is There a Special Tool to Remove Kitchen Faucet Handle?

When it comes to removing a kitchen faucet handle, you don’t necessarily need a special tool to do the job. In many cases, all you need is an adjustable wrench and maybe some lubricant or penetrating oil.

Depending on the make and model of your faucet, there may be screws that attach the handle directly to the stem or cartridge, in which case a standard screwdriver should do the trick.

If those methods are unsuccessful, however, then you may need to invest in a specialized tool for removing faucets handles.

A few common examples include flathead screwdrivers with L-shaped tips (for pushing pins out), stem pullers (for pulling stems out of cartridges) and pin extractors (for removing setscrews).

These tools can be found at most hardware stores, so if you’re having difficulty getting your handle off then it’s worth checking out.

No matter what kind of tool you end up using, remember that removing a kitchen faucet handle requires patience and a careful approach.

Do your best to avoid any unnecessary force or damage, as this could result in more costly repairs down the road.

Conclusion

If your faucet has a screwless handle, you may be wondering how to remove it. The good news is that there is no special tool required to remove a kitchen faucet handle without screws.

You can use a regular flathead screwdriver or an Allen wrench. With the right tools and a little know-how, you can easily remove a screwless faucet handle.

Leave a Reply

Your email address will not be published. Required fields are marked *